Launch offer: add a second pattern and it is half price. The discount applies itself at checkout.Second pattern half price, applied at checkout USD $GBP £
Sewing techniques

Hand sewing stitches: 8 essential stitches and when to use them

By · Published

Nina boat-neck shift dress sewing pattern: a photo-realistic preview rendered from the CLO 3D pattern beside the back and front pattern pieces
Sew it: the Nina boat-neck shift dress · from $16.00

A note on measurements: this guide is written for US sewists, so it uses US units first: inches, yards and US paper sizes (Letter, 36 × 48 in). Metric equivalents are in brackets where they matter. If you're not used to US measurements, convert them before you cut: 1 in = 2.54 cm, 1 yd = 91.4 cm.

Most garments need only eight hand sewing stitches: the running stitch, basting stitch, backstitch, prick stitch, slip stitch, blind hem stitch, catch stitch and whipstitch. The first four join and hold fabric; the last four finish edges, hems and openings so the stitches barely show. Even if you sew almost everything on a machine, these are the stitches that close a lining, hem a pair of wide-leg pants invisibly and tack a facing so it stays inside.

Nina sewing pattern on a 3D body in CLO 3D, front view, with its pattern pieces drawn to scale
Draped in CLO 3D: the Nina with its pattern pieces, drawn to scale.

Before you start: needle, thread and tension

Good hand stitching is mostly setup. Get these right and the stitches come out even.

If you are right-handed, most stitches below are worked from right to left; the catch stitch is the exception and goes left to right. Left-handed sewists can reverse all directions.

Stitches for joining and holding fabric

Running stitch

The simplest stitch, used for gathering, mending and easing.

  1. Knot the thread or lock it with two tiny stitches.
  2. Weave the needle in and out of the fabric, taking stitches about 1/8 to 1/4 in (3 to 6 mm) long with gaps of the same size.
  3. On thin fabric, load three or four stitches onto the needle before pulling through. On thick fabric, stab one stitch at a time.
  4. Finish with a backstitch.

Basting stitch

A long, temporary running stitch that holds layers in place before machine sewing, or lets you check fit.

  1. Use a contrasting color so it is easy to find and remove.
  2. Take stitches about 1/2 in (1.3 cm) long with 1/2 in (1.3 cm) gaps, or alternate one long and one short stitch (uneven basting) on straight seams.
  3. Don’t knot the end tightly; you will pull it out later.

Backstitch

The strongest hand stitch, and the one to use for hand-sewn seams and repairs.

  1. Bring the needle up one stitch length ahead of where you want the seam to start.
  2. Insert it back at the start, then bring it up one stitch length ahead of where the thread last came out.
  3. Keep going back into the end of the previous stitch, with each stitch 1/16 to 1/8 in (1.5 to 3 mm) long. The top looks like machine stitching; the underside stitches are twice as long and overlap.

Prick stitch

A backstitch where you go back only one or two threads instead of a full stitch length. On the right side you see tiny dots spaced 1/8 to 1/4 in (3 to 6 mm) apart. It is used for hand-picked zippers and to understitch or anchor layers neatly where machine stitching would be too visible.

Stitches for hems and finishing edges

Slip stitch (ladder stitch)

The most invisible stitch for joining two folded edges, such as a lining gap, a turning opening on a tie sash or a mitered hem corner.

  1. Hide the knot inside one fold.
  2. Run the needle inside that fold for about 1/4 in (6 mm), bring it out, then cross straight over to the opposite fold.
  3. Slide the needle inside the second fold for 1/4 in (6 mm), come out, and cross straight back. The crossing threads look like the rungs of a ladder.
  4. Every 1 to 2 in (2.5 to 5 cm), pull the thread gently to close the gap. The stitches disappear into the folds.

For hemming, a slip stitch is worked the same way but takes only one or two threads of the garment opposite the fold each time, with stitches about 1/4 in (6 mm) apart. The guide on how to hem a dress shows which hem depth and stitch suit each skirt shape.

Blind hem stitch

Hides the thread between the hem allowance and the garment, so nothing shows on either side.

  1. Fold the hem up and press. Roll the top edge of the hem allowance back toward you by about 1/4 in (6 mm).
  2. Take a tiny stitch in the garment, catching one or two threads only.
  3. Move 1/4 to 1/2 in (6 mm to 1.3 cm) to the left and take a small stitch in the hem allowance.
  4. Repeat, keeping the thread relaxed. When you let the hem edge fall back, the stitches are hidden underneath it.

Catch stitch (herringbone stitch)

A crossed zigzag stitch that stretches, so it is the best hem for knits, bias-cut skirts and fluid fabrics that move. It also holds facings and interfacing edges flat.

  1. Work from left to right with the needle pointing left.
  2. Take a small stitch in the hem allowance, about 1/4 in (6 mm) below its edge.
  3. Move about 1/4 in (6 mm) to the right and take a tiny stitch in the garment just above the hem edge, catching one or two threads.
  4. Move another 1/4 in (6 mm) to the right and stitch the hem allowance again. The threads cross each other in an X pattern.
  5. For a blind catch stitch, roll the hem edge back as for the blind hem stitch and work the catch stitch underneath it.

Whipstitch and fell stitch

A whipstitch loops over an edge with small slanted stitches, about 1/8 in (3 mm) apart. Use it to join two finished edges, attach a patch or tame a fraying raw edge. A fell stitch (hemming stitch) is a small, close slanted stitch that holds a folded edge flat to the fabric beneath. It is firmer than a slip stitch and is the stitch for sewing linings to seam allowances and finishing bias binding by hand.

Hand stitches in Patterns by Nini designs

The Tobi pinafore overall mini dress is sewn mainly by machine, but a few hand stitches give it a cleaner finish:

The Nina shift dress has a faced neckline and a center-back invisible zipper, so you can also slip stitch the facing ends to the zipper tape, clear of the teeth. The invisible zipper guide covers the zipper itself.

Common mistakes and how to fix them

ProblemLikely causeFix
Thread twists and knotsThread too long, or twisting as you sewCut it arm’s length, wax it, and let the needle dangle to untwist every few stitches
Hem stitches show on the right sideToo much fabric caught in the garment sidePick up only one or two threads; use a fine sharp needle
Fabric puckers along the hemStitches pulled too tightKeep the thread relaxed; on fluid fabric, use a catch stitch
Hem pops when you sit or walkNo stretch in the stitchUse a catch stitch; lock the thread with a backstitch every 4 to 6 in (10 to 15 cm) so one break doesn’t undo the whole hem
Knot pulls through the fabricKnot too small for a loose weaveStart with two tiny backstitches instead of a knot
Slip-stitched gap looks lumpyFolds not pressed, or crossings at an anglePress the folds first and cross straight over each time

Quick reference

If you’re new to garment construction, the guide to seams and seam allowances explains how the pieces these stitches finish are put together.

Frequently asked questions

What is the strongest hand sewing stitch?
The backstitch is the strongest everyday hand stitch. Each stitch doubles back over the one before it, so the thread forms a continuous line like machine stitching, with no gaps for the seam to pull open. Use it for hand-sewn seams, repairs on stress points such as crotch and underarm seams, and for securing the start and end of other stitches.
Which hand stitch is invisible?
The slip stitch, also called the ladder stitch, is the most invisible hand stitch. The thread travels inside the folds of the fabric and only crosses briefly between them, so almost nothing shows when you pull it snug. Use it to close turning gaps and linings. For hems, the blind hem stitch and blind catch stitch hide the thread just as well.
Should you hand sew with a single or double thread?
Use a single strand for most garment sewing, including hems, slip stitching and basting, because it is finer, less visible and tangles less. Use a double strand when strength matters more than looks, such as sewing on buttons, hooks and snaps, or mending a seam that takes strain. Either way, cut the thread no longer than your arm.
How do you start and finish hand stitching without a knot?
To start, take a small stitch on the wrong side or inside a seam allowance, leaving a short tail, then work two tiny backstitches on top of it to lock the thread. To finish, take two or three small backstitches in the same spot, run the needle between the fabric layers for about 1 in (2.5 cm), bring it out and trim the thread close.

Sources

Your cart

Loading your cart…