Launch offer: add a second pattern and it is half price. The discount applies itself at checkout.Second pattern half price, applied at checkout USD $GBP £
Learn to sew

How to sew a T-shirt: a step-by-step guide for beginners

By · Published

Sola fitted T-shirt sewing pattern: a photo-realistic preview rendered from the CLO 3D pattern beside the front, back, sleeve and neckband pattern pieces
Sew it: the Sola fitted t-shirt · from $10.00

A note on measurements: this guide is written for US sewists, so it uses US units first: inches, yards and US paper sizes (Letter, 36 × 48 in). Metric equivalents are in brackets where they matter. If you're not used to US measurements, convert them before you cut: 1 in = 2.54 cm, 1 yd = 91.4 cm.

To sew a T-shirt, cut the front, back, sleeves and neckband from a stretch knit, then sew them in this order: shoulders, neckband, sleeves (set in flat), one continuous seam from sleeve hem to body hem on each side, and finally the hems. Use a ballpoint needle and a stitch that stretches, such as a narrow zigzag, and you can do it all on a regular sewing machine. That order is how to sew T-shirts quickly and neatly, because almost every seam is sewn while the pieces still lie flat.

Sola sewing pattern on a 3D body in CLO 3D, front view, with its pattern pieces drawn to scale
Draped in CLO 3D: the Sola with its pattern pieces, drawn to scale.

This guide follows that order step by step, with stitch settings, the neckband method that gets a flat neckline, and fixes for the problems knits usually cause.

What you need

Check the stretch of your fabric

Fold the fabric along the crosswise direction, mark 4 in (10 cm) and stretch that section gently across the width until it resists. If it reaches 5.2 in (13.2 cm), it has 30% stretch; 6 in (15 cm) is 50%. Then let go: a good T-shirt knit springs straight back. If the stretch is less than the pattern asks for, the tee will fit tighter and the neckband may not go over your head.

Prewash and dry the fabric the way you will wash the finished tee. Cotton jersey often shrinks in length.

Cut the pieces

  1. Lay the fabric flat on a table, with nothing hanging off the edge to pull it out of shape.
  2. Line up the grainline on each piece with the ribs of the knit (the lengthwise lines you can see on the right side). The stretch should run around the body.
  3. Cut the front and back on the fold, and two sleeves as a mirrored pair.
  4. Cut the neckband with its stretch running along its length.
  5. Snip notches at the center front, center back and sleeve cap center, and mark the shoulder points.

A rotary cutter and mat stop jersey from shifting as you cut.

How to sew a T-shirt, step by step

Set a narrow zigzag about 1 to 1.5 mm wide and 2.5 to 3 mm long, or use the lightning-bolt stretch stitch. Use a 3/8 in (1 cm) seam allowance unless your pattern says otherwise. Test on a double layer of scrap first.

1. Sew the shoulder seams

  1. Place the front on the back, right sides together, and pin the shoulders.
  2. For a tee that keeps its shape, lay a strip of clear elastic or knit stay tape over the seam line.
  3. Stitch, then press the seam allowances toward the back with a warm iron.

Shoulders are where a knit top stretches out first, so the tape is worth the extra minute.

2. Attach the neckband

  1. Measure the neckline along the seam line, not the raw edge.
  2. Check the band length. If your pattern gives a neckband piece, use it. If you are drafting one, start at about 85% of the neckline length for jersey and a little shorter for rib knit.
  3. Sew the band into a loop, right sides together, and press the seam open. Fold it in half lengthwise, wrong sides together.
  4. Quarter it. Mark the band in four equal parts, with the band seam at one mark. Mark the neckline in four parts too: center back, center front and the two points halfway between.
  5. Pin the band to the right side of the neckline, raw edges together, band seam at center back, matching the four marks. The band will be shorter than the neckline between pins.
  6. Sew with the band on top. Stretch only the band, just enough to lie flat against the neckline, and let the machine feed the fabric. Don’t pull from behind.
  7. Press the seam allowance toward the body with steam, then topstitch about 1/8 in (3 mm) from the seam on the shirt side, with a twin needle or a narrow zigzag.

Some patterns attach the band flat, before the second shoulder seam is sewn. The quarter-pinning works the same way; you just close the last shoulder and band end in one seam afterward.

3. Set the sleeves in flat

  1. Match the sleeve cap notch to the shoulder seam, right sides together.
  2. Pin the ends of the sleeve to the ends of the armhole, then pin in between.
  3. Sew from the center out to each side, or straight across with the sleeve on the bottom so the feed dogs ease it in.
  4. Press the seam allowances toward the sleeve.

Knits ease in without basting. For more on this flat method and when to set a sleeve in the round instead, see how to sew sleeves.

4. Sew the side seams

  1. Fold the tee right sides together and match the underarm seams first.
  2. Pin from the sleeve hem through the underarm to the body hem.
  3. Sew in one continuous seam on each side.

Try the tee on now, before hemming. This is the time to take in the sides or shorten the length.

5. Hem the sleeves and body

Fold up the hem allowance, usually 3/4 to 1 in (2 to 2.5 cm), and press without dragging the iron. A strip of fusible knit interfacing or fusible web in the fold keeps it flat. Stitch from the right side with a twin needle or a narrow zigzag. The full method, including coverstitch and hand-sewn options, is in how to hem a T-shirt.

Common mistakes and how to fix them

ProblemLikely causeFix
Wavy or rippled seamsFabric stretched as it fedLengthen the stitch, lower presser foot pressure, use a walking foot, steam press
Neckband stands away from the neckBand too longUnpick and shorten the band by 3/4 to 1 in (2 to 2.5 cm)
Neckline puckers or pullsBand too short, or stretched unevenlyLengthen the band slightly; re-pin at the quarter marks
Skipped stitchesWrong or blunt needleFit a new ballpoint or stretch needle
Stitches snap when you pull the tee onStraight stitch with no stretchResew with a narrow zigzag or stretch stitch
Fabric gets pushed into the needle plateSeam started right at the edgeStart 3/8 in (1 cm) in, or hold the thread tails as you begin

If a seam is only slightly wavy, hold a steam iron just above it and pat it flat. Many cotton jerseys shrink back into shape.

Patterns by Nini T-shirt patterns

The Sola fitted tee is a good tee to practice these steps on. It is a classic short-sleeve crew-neck tee in six steps, sewn flat, with a sew-in neckband and short set-in sleeves that are set in flat. It has 2 in (5 cm) of ease at the bust, so it sits close without clinging, and a hip-length hem about 25 in (64 cm) at the back in size M. It comes in sizes S to XXL, rated beginner for knits, for cotton or viscose jersey with at least 30% widthwise stretch.

For a looser fit, the Wura oversized tee has dropped shoulders and a boxy body. The Tade boat-neck tee swaps the crew neck for a wide, shallow boat neckline with a narrow band, and the Lola rib top is a long-sleeve version in rib knit with a high crew rib neckband. Once you can sew a tee, the Dupe T-shirt midi dress uses the same neckband and set-in sleeves on a pull-on dress with side slits.

If this is one of your first projects, the guide to sewing patterns for beginners covers what to make next.

Frequently asked questions

Can you sew a T-shirt without a serger?
Yes. A regular sewing machine sews a T-shirt well with a ballpoint or stretch needle and a stitch that stretches, such as a narrow zigzag or a lightning-bolt stretch stitch. Jersey doesn't fray, so the seam allowances can stay raw. A serger is faster and gives a ready-to-wear finish, but it is optional. Hem with a twin needle or a zigzag.
What fabric is best for a first T-shirt?
A medium-weight cotton jersey with some spandex is the easiest first choice. It is stable enough to cut accurately, it presses well and the spandex helps it spring back. Check your pattern's stretch requirement before you buy. Very thin, slinky or very stretchy knits such as rayon jersey are harder to control and are better for your second or third tee.
How long should a T-shirt neckband be?
Shorter than the neckline, so it can be stretched to fit and lie flat. A common starting point is about 85% of the neckline seam length, but the right length depends on how stretchy the band fabric is. Rib knit can be cut shorter than self-fabric jersey. If your pattern includes a neckband piece, use it, and pin it around the neck before sewing to check.
What stitch should I use to sew a T-shirt?
Use a narrow zigzag about 1 to 1.5 mm wide and 2.5 to 3 mm long, or your machine's lightning-bolt stretch stitch, for the seams. Both stretch with the fabric, so the seams won't pop when you pull the tee over your head. A plain straight stitch can snap on a fitted tee. Test on a scrap of the same fabric first.
How long does it take to sew a T-shirt?
Once the pattern is printed and the fabric is cut, a simple crew-neck tee is usually an afternoon's work for a beginner and about an hour or two with practice. Cutting and taping the pattern takes the most time on the first make. The neckband is the slowest step, so give it time and don't rush the pinning.

Sources

Your cart

Loading your cart…